Other/Central Govt/CPPP

Alignment (Distortion) Checking Gauge

by Ministry of Railways

Published
Thu, 17 Sept
4:07 pm
Bid submission closes
Mon, 5 Oct
1:30 pm· 7 days left
Bid opening
Mon, 5 Oct
1:30 pm

Tender details

Organisation: Ministry of Railways
Location: Central Government
Tender ID: 107187660
Reference no.: 54266330
Category: Other
Source portal: CPPP — Central Public Procurement Portal

How to bid

1Open CPPP — Central Public Procurement Portal and search for Tender ID 107187660 under Active Tenders (or Tenders by Organisation).
2Download the tender documents and any corrigenda. Check eligibility, EMD and the document fee.
3Register on the portal as a bidder with a Class 3 Digital Signature Certificate (DSC), then upload your bid before the closing time.

Similar live tenders

Other in Central Govt →

Complete servicing of Scorpio S11 oil filter fuel filter air filter eng oil change transfer case oil brake fluid wheel alignment and suspension checking Veh Ba No 24B 140809P, Rubber bush lower MG, U clamp ALS, Engine oil filling cap ALS, Fog light ALS, Armature assy 24V TATA
Department of Military Affairs · Central Govt
Sat, 3 Oct6:00 pm · 5 days left
Bolster twist checking gauge.
Ministry of Railways · Central Govt
Mon, 5 Oct11:00 am · 7 days left
Gauge for Checking of Anti-Creep Ledge of Bottom Lifter Gauge
Ministry of Railways · Central Govt
Thu, 8 Oct10:30 am · 10 days left
Manufacturing and Supply of complete set of RDSO/T- 9003 Alt-03 Inspection gauge for 10125 mm curved switch with 60E1A1 thick web tongue rails for 1 in 12 turnout B.G. (1673 mm) for 60E1 rail on PSC sleepers to drawing No. RDSO/T- 6155 for use in depot as per drawing no. RDSO/T-9003(Part). One set consist of the following: 1) End Template at Actual toe of Switch (Gauge no. 1)2) Head width checking gauge at 2678mm from ATS, 22mm head thickness (Gauge no. 2A & 2B)3) Head width checking combined
Ministry of Railways · Central Govt
Tue, 29 Sept11:30 am · Tomorrow
Set of CBC gauges One set consist of 06 gauges for checking of AAR H type Centre Buffer Coupler ofLHB coaches. Gauges made of hard steel alloy or stainless steel with Hardness 45-50 HRC as per attachedspecifications (i) Contour Maintenance gauge (Knuckle profile gauge): APTA drawing/Gauge No.31000 (ii) AligningWing Limit gauge: APTA drawing/Gauge No. 32600 (iii) Contour Condemning Limit Gauge (Jaw-gap gauge) APTAdrawing/Gauge No. 34100-1 (iv) Knuckle Nose wear and stretch limit gauge: APTA dra
Ministry of Railways · Central Govt
Wed, 7 Oct2:25 pm · 9 days left
Replacement of rear axle bearing, Replacement of rear wheel oil seal, Replacement of rear wheel break shoe, Repair of rear wheel drum, Replacement of front wheel oil seal, Replacement of front wheel break shoe, Repair of front wheel drum, Repair of rear break cylinder, Fuel filter Primary, Fuel filter Secondary, Lub oil filter, Filter cover assy, Sealing washer, Air Filter Element, Maintaining the level of gear box oil, Break oil Half Ltr, Collant with distilled water, Replacement of Engine Oil 6.5 Ltr, Four wheel hub greasing Castrol with Hub seal, Four wheel Alignment, Replacement of front suspension Bush kit, Replacement of Tie rod end assembly, Replacement of Centre arm bush kit, Replacement of Lower arm ball joint, Replacement of Upper arm ball joint, Replacement of support bracket of FIP with weld nut, Timeing gear cover seal replacement, Fuel Injection pump caliberation, Cleaning and Greasing of nipple in the full vehicle., Engine tune-up and timing adjustment, Four Door rattling checking., Replacement of Starter motor including sta
Department of Military Affairs · Central Govt
Mon, 28 Sept6:00 pm · Today

Alignment (Distortion) Checking Gauge

Tender details

How to bid

More from Ministry of Railways

Similar live tenders